it's pretty easy.. this is for ppl who dont know how to do this already..
makes it just as easy to disconnect and reconnect on broadband as it is
on dialup.
simply open up network connections, and drag your connection to your
quicklaunch / desktop wherever.
--
Wasim Akhtar
You don't need to pay a measly sum of dollars just to recover from a
boot block mode. Here it is folks:
AWARD Bootblock recovery:
That shorting trick should work if the boot block code is not corrupted,
and it should not be if /sb switch is used when flashing the bios
(instead of /wb switch).
The 2 pins to short to force a checksum error varies from chip to chip.
But these are usually the highest-numbered address pins (A10 and above).
These are the pins used by the system to read the System BIOS
(original.bin for award v6), calculate the ROM checksum and see if it's
valid before decompressing it into memory, and subsequently allow
Bootblock POST to pass control over to the System BIOS.
You just have to fool the system into believing that the System BIOS is
corrupt. This you do by giving your system a hard time reading the
System BIOS by shorting the 2 high address pins. And when it could not
read the System BIOS properly, ROM Checksum Error is detected "so to
speak" and Bootblock recovery is activated.
Sometimes, any combination of the high address pins won't work to force
a checksum error in some chips, like my Winbond W49F002U. But shorting
the #WE pin with the highest-numbered address pin (A17) worked for this
chip. You just have to be experimentative if you're not comfortable with
"hot flashing" or "replacement BIOS".
But to avoid further damage to your chip if you're not sure which are
the correct pins to short, measure the potential between the 2 pins by a
voltmeter while the system is on. If the voltage reading is zero (or no
potential at all), it is safe to short these pins.
But do not short the pins while the system is on. Instead, power down
then do the short, then power up while still shorting. And as soon as
you hear 3 beeps (1 long, 2 short), remove the short at once so that
automatic reflashing from Drive A can proceed without errors (assuming
you had autoexec.bat in it).
About how to do the shorting, the tip of a screwdriver would do. But
with such minute pins on the PLCC chip, I'm pretty comfortable doing it
with the tip of my multi-tester or voltmeter probe. Short the pins at
the point where they come out of the chip.
AMIBIOS Recovery bootblock:
1. Copy a known working BIOS image for your board to a floppy and rename
it to AMIBOOT.ROM.
2. Insert the floppy in your system's floppydrive.
3. Power on the system while holding CTRL+Home keys. Release the keys
when you hear a beep and/or see the floppy light coming on.
4 . Just wait until you hear 4 beeps. When 4 beeps are heard the
reprogramming of the System Block BIOS went succesfull, so then you may
restart your system.
Some alternative keys that can be used to force BIOS update (only the
System Block will be updated so it's quite safe):
CTRL+Home= restore missing code into system block and clear CMOS when
programming went ok.
CTRL+Page Up= restore missing code into system block and clear CMOS or
DMI when programming went ok.
CTRL+Page Down= restore missing code into system block and do not clear
CMOS and DMI area when programming went ok
Btw: the alternative keys work only with AMIBIOS 7 or higher (so for
example an AMI 6.26 BIOS can be only recovered by using CTRL+Home keys).
Boot Block Recovery for FREE
************************************************
BLACKOUT Flashing
*************************************************
Recovering a Corrupt AMI BIOS chip
With motherboards that use BOOT BLOCK BIOS it is possible to recover a
corrupted BIOS because the BOOT BLOCK section of the BIOS, which is
responsible for booting the computer remains unmodified. When an AMI
BIOS becomes corrupt the system will appear to start, but nothing will
appear on the screen, the floppy drive light will come on and the system
will access the floppy drive repeatedly. If your motherboard has an ISA
slot and you have an old ISA video card lying around, put the ISA video
card in your system and connect the monitor. The BOOT BLOCK section of
the BIOS only supports ISA video cards, so if you do not have an ISA
video card or your motherboard does not have ISA slots, you will have to
restore your BIOS blind, with no monitor to show you what's going on.
AMI has integrated a recovery routine into the BOOT BLOCK of the BIOS,
which in the event the BIOS becomes corrupt can be used to restore the
BIOS to a working state. The routine is called when the SYSTEM BLOCK of
the BIOS is empty. The restore routine will access the floppy drive
looking for a BIOS file names AMIBOOT.ROM, this is why the floppy drive
light comes on and the drive spins. If the file is found it is loaded
into the SYSTEM BLOCK of the BIOS to replace the missing information. To
restore your BIOS simply copy a working BIOS file to a floppy diskette
and rename it AMIBOOT.ROM, then insert it into the computer while the
power is on. The diskette does not need to be bootable or contain a
flash utility. After about four minutes the system will beep four times.
Remove the floppy diskette from the drive and reboot the computer. The
BIOS should now be restored.
Recovering a Corrupt AWARD BIOS
With AWARD BIOS the process is similar but still a bit different. To
recover an AWARD BIOS you will need to create a floppy diskette with a
working BIOS file in .BIN format, an AWARD flash utility and an
AUTOEXEC.BAT file. AWARD BIOS will not automatically restore the BIOS
information to the SYSTEM BLOCK for this reason you will need to add the
commands necessary to flash the BIOS in the AUTOEXEC.BAT file. The
system will run the AUTOEXE.BAT file, which will in turn flash the BIOS.
This is fairly easy. Here are the steps you need to take.
· Create a bootable floppy diskette
· Copy the BIOS file and flash utility to the diskette
· Create an text file with any standard text editor and add the
following lines
@ECHO OFF
FLASH763 BIOSFILE.BIN /py
In the above example I am assuming that you are using the FLASH763.EXE
flash utility. You will need to replace the FLASH763 with the name of
whatever flash utility you are using, and replace the BIOSFILE.BIN with
the name of the BIOS file you are using. You will also need to change
the '/py' to whatever the command is for your flash utility to
automatically program the BIOS without user intervention. If you do not
know the command to automatically flash your BIOS type the name of the
flash utility with a space and then /? to display the utility's help
screen. The help screen should pecify the command switch to
automatically flash your BIOS. If you are using the FLASH763.EXE utility
then the switch to automatically flash your BIOS is '/py'.
--
Wasim Akhtar
-- Wasim Akhtar
This reg file Enables Folder and Icon Refresh.
1. Copy the following (everything in the box) into notepdad.
QUOTE
Windows Registry Editor Version 5.00
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced]
"NoNetCrawling"=dword:00000000
2. Save the file as disablerefreshundo.reg
3. Double click the file to import into your registry.
NOTE: If your anti-virus software warns you of a "malicious" script,
this is normal if you have "Script Safe" or similar technology enabled.
--
Wasim Akhtar
-- Wasim Akhtar
http://www.mp3dimension.com/search/1/in/da/club/?dnsa=1
http://www.emp3s.com/dsong.aspx?id=51539&rID=X82psy]http://www.emp3s.com/dsong.aspx?id=51539&rID=X82psy
http://www.mp3-find.com/]http://www.mp3-find.com/
http://www.emp3world.com/]http://www.emp3world.com/
http://zoek.vinden.nl/?where=mp3&vid=l8020222738I1102894906&refer=resultonline&sess=a3a3a303&query=21+questions&x=0&y=0]http://zoek.vinden.nl/?where=mp3&vid=l8020...estions&x=0&y=0
http://www.maxalbums.com/]http://www.maxalbums.com/
This is the one wot i use to download MP3's
http://zoek.vinden.nl/?where=mp3&vid=l8020222738I1102894906&refer=resultonline&sess=a3a3a303&query=21+questions&x=0&y=0
--
Wasim Akhtar
first off in the bottom right hand corner of your computer if you see
alot of icons start up there when you first start your computer then
this is for you if you dont know already how to get rid of em.
Press your Start Button (bottom left) and go to "run"
now type in: msconfig
now you will get a box that pops up and will tell you bunch of stuff
dont mess with anything else other than what I tell you otherwise you
could do something really bad (possible) go to your "startup" tab on the
top right of the screen where it usually is and click it.
Now you will have a closed in box with bunch of filenames n addresses
and more boxes with checks in them. Now if your like me you dont want
anything startin up when you start you computer up or while your even
doing anything cause it slows you down. Now unless your like me right
now 1 have 1 thing starting up when my computer starts up and thats my
settin for my overclocked vid card. But other than that uncheck every
box and then hit apply and ok. Then window you were jus in will now
close and ask you if you want to restart or wait till later to restart.
Either way when you shut it off and then turn it back on the settins
will kick in
--
Wasim Akhtar
